The car engine is the most important power system of the car. The components inside are also very tight and can not be damaged. The air filter is a part of the engine protection, so the air filter needs to be replaced or maintained regularly. Here are some of the relevant knowledge about air filters that Xiaobian has compiled for the riders. It is equivalent to the human nose, the “level†of the passage of air into the engine. The function is to finely filter the air entering the engine cylinder, filter out the sand in the air and some suspended particles, so that the air entering the engine is compared. Pure, so it is especially important for its maintenance. Below I am here to check the maintenance method of the air filter for everyone, I hope to be helpful to the majority of car owners. Regularly clean the air conditioner filter If the air filter is the "nose" of the car, then the air conditioner filter is directly related to whether the nose of the passenger in the car can breathe healthy air. The air entering the interior of the compartment from the outside is filtered to improve the cleanliness of the air and ensure the health of the passengers inside the vehicle. It is important to keep the air conditioner filter clean if the vehicle frequently passes through dusty roads. In the colder temperatures in winter, some car owners close the windows when driving, only open the inner circulation and do not open the air conditioner. The master pointed out that this is not correct. After a long time driving, the air inside the car will be turbid. Health brings certain hidden dangers. Normally, when the vehicle travels 8,000 km to 10,000 km, the air conditioner filter needs to be replaced once. Usually, it only needs to be cleaned regularly during each season, especially after the winter. Air conditioner filters can also be cleaned by yourself, which is not difficult. How to maintain the air filter? According to the maintenance cycle of the vehicle, in the case of general roads, the air filter should be cleaned and maintained every 5,000 kilometers. In areas with large dust and sand and poor ambient air quality, the maintenance interval should be shortened accordingly. The master recommends cleaning up every 3,000 km in advance. The air filter of a general car should be changed once when the car is driving 20,000 kilometers. DIY clean air filter Preparation tool: screwdriver 1. Stop the fire and stop. Make sure the vehicle is turned off and cool for 15~20 minutes, then open the engine compartment cover and locate the air filter. The air filter is usually located on the right side of the engine compartment and can be found in the vehicle's manual. 2. Take the filter. Open the filter cover latch, remove the nut that secures the cover, pull the bezel open, and remove the filter element. When removing the filter element, take care to prevent impurities from falling into the carburetor. 3. Clean the filter element. Check the filter element for more dust. You can gently tap the end face of the filter element. You can use compressed air to blow off the dust from the filter element. If there is no compressed air, tap the filter element with a screwdriver handle and brush the external dirt with a brush. Never use petrol or water wash brushes. If the air filter has been severely blocked, it needs to be replaced with a new one. 4. After the filter element has been cleaned, install the parts in the reverse order of removal. The air filter is the last level of the engine, the key to protect the engine from damage, so the riders must pay attention to the maintenance of the air filter.
Little Elephant Tool offers many products for
Granite and Stone Installation. From Clamps to suction cups, we've got the
tools needed for installation suction cup sizing includes: 45° Stone Mitre
Clamp, Vacuum Stone Seam
Setter, 45° Stone Mitre
Clamp(Metal handle with nylon feet), 45° Stone Mitre Clamp enlarge type, Stone Sink Hole Saver, Mini Seam Setter, Hand Carry Clamps, Self Locking Trolley.
Product Name: 45°
Stone Mitre Clamp(Plastic handle with metal feet)
Model
Max Processing Height(mm)
Size(mm)
Weight(kg)
Pcs/Ctn
FRMC-1
130
210x66x335
2.5
6
1.45 ° Mitre Clamp
is mainly use for the stone sheet stitching, It can aslo used
for other similar sheet of 45 stitching.
2.When two
workpieces are processed into a 45 edge bevel, then clean the 45 face of
workpiece, evenly coated with adhesive, then put two workpiece of 45 bevel face
assembling together, and the two 45°workpiece fit into a 90 with each other,
use the fixture in plastic extrusion seam stitching.
3.First, put the
bottom of width stone on the fixture work surface which with white rubber, the side
of the narrow stone close to the 90 inside of the fixture.
4.Then two binder
lever can be adjusted by adjusting spring device access to the top position of
the workpiece,then rotating the screw at the top of the binder lever to put
pressure in place to maintain the fixture locked position for a certain time,
until the workpiece fully bonded joints, solid, and then release the
fixture.
Stone Install And Carry Tools,Stone Edge Profile Wheels,Stone Install Tools,Stone Carry Toolsc Shandong Hightop Machinery Co,.Ltd , https://www.hightopmachinery.com
September 15, 2019